FAQs
_______
Slider

Check here for answers to your most common questions.

FREQUENTLY ASKED QUESTIONS

Need more information? Contact us online, or, Ask An Engineer.

GENERAL

Porex offers many possible shapes: three-dimensional parts, sheets, tubes, rods, and profiles are among your options. While there are some limitations depending on base material, size, and geometry, we frequently review drawings so our engineers can recommend options that can meet your application needs.

The majority of Porex parts are naturally white. However, colors and blacks are available by request, and colored specs can be added to designate properties.

Most thermoplastics can be made porous, although some materials do better with our proprietary processes than others. We have worked with numerous resins throughout the years and we can recommend one or more material solutionsdepending on your needs.

POREX® Porous Plastics are used in numerous applications that involve filtering, venting, wicking, diffusion, fluid and gas control, media support, and many other related applications. Because our products are used in so many varied applications, Consult a Porex Expert to determine how Porex solutions can meet your application requirements.

Teflon® is a registered trademark of E. I. du Pont de Nemours and Company for the chemical material generically known as polytetrafluoroethylene or PTFE. Porex does offer a line of microporous PTFE materials utilized in many industries.

Yes, porous plastics can be combined with additives. Because there are so many options, we recommend you Consult a Porex Expert to discuss your options.

Most of our products are custom made to customer specifications. Please Consult a Porex Expert in your region to discuss your specific application needs.

Porex utilizes numerous raw materials with various regulatory approvals. We recommend you Consult a Porex Expert who can guide you to your best product options for your application.

TECHNICAL

No. Typical porous polytetrafluoroethylene (PTFE) is expanded PTFE (e-PTFE) where porosity is created by micro-fracturing the membrane by controlled stretching. POREX® PTFE Membrane is sintered and skived so porosity and dimensions are well controlled and consistent. Compared with e-PTFE, Porex microporous PTFE solutions are more robust and available in a wider range of porosity and thickness ranges, as well as custom shapes.

Whether sealing or bonding agents can be used depends on the base material. Polyethylene (PE), polypropylene (PP), and polytetrafluoroethylene (PTFE) resist most solvents and are difficult to solvent bond. Some of the following are better choices for sealing or bonding these materials: PVC or ABS cement, two-part epoxy systems, or silicone sealant. It is important to note that many of these choices may cause the final part to lose some of its porosity, as the sealant will close off some of the pores.

Porous plastic can be sterilized similarly to its corresponding solid non-porous parts. For example, polyethylene (PE) and polypropylene (PP) can be sterilized by ethylene oxide (EtO), radiation, and stream; polytetrafluoroethylene (PTFE) can be sterilized with EtO and steam.

Since porous plastics have a certain amount of void volume, yes, they are somewhat compressible. How compressible will depend on material, porosity, and part geometry.

Yes. We have worked with several elastomeric materials and can make flexible porous parts.

Yes, porous plastics can be combined with additives. Because there are so many options, we recommend you consult a Porex expert to discuss your options.

Most of our products are custom made to customer specifications. Please Consult a Porex Expert in your region to discuss your specific application needs.

Porex utilizes numerous raw materials with various regulatory approvals. We recommend you Consult a Porex Expert who can guide you to your best product options for your application.

MECHANICAL / MANUFACTURING

No. Porex utilizes a proprietary forming/molding process. In general, part geometries can be similar to injection molding parts.

Yes. In general, POREX® Porous Plastics can be sawed, turned, milled, drilled, punched, or cut. It is best to keep the surface temperature low and cutting instrument sharp to prevent surface smear. Machinability also depends on the base material selection.

In general heat welding is best, as some porous materials can absorb vibrational energy, which can cause inconsistency. Properties will be dependent on the final material choice.

Yes. At Porex, we make custom prototype and production tooling.

Sheets up to 42 inches wide are possible. Typical maximum width for polytetrafluoroethylene (PTFE) sheets is about 13 inches, although somewhat wider sheets can be custom made.

Sheets up to 42 inches wide are possible. Typical maximum width for polytetrafluoroethylene (PTFE) sheets is about 13 inches, although somewhat wider sheets can be custom made.